FZ 3.39.0 doesn't see var/www

Need help with FileZilla Client? Something does not work as expected? In this forum you may find an answer.

Moderator: Project members

Post Reply
Message
Author
geomcd1949
500 Command not understood
Posts: 5
Joined: 2019-01-25 01:59
First name: George

FZ 3.39.0 doesn't see var/www

#1 Post by geomcd1949 » 2019-01-25 02:27

Upgraded to FZ 3.39.0 on Ubuntu 18.04. Previously FZ worked perfectly. Upgrade doesn't show the www folder within Local Site /var/ [It lists only data, run, db, config,cache, and tmp].

Thanks.

~George

User avatar
botg
Site Admin
Posts: 31800
Joined: 2004-02-23 20:49
First name: Tim
Last name: Kosse
Contact:

Re: FZ 3.39.0 doesn't see var/www

#2 Post by botg » 2019-01-25 07:59

Do you by chance have directory listing filters enabled?

geomcd1949
500 Command not understood
Posts: 5
Joined: 2019-01-25 01:59
First name: George

Re: FZ 3.39.0 doesn't see var/www

#3 Post by geomcd1949 » 2019-01-26 03:20

I don't know how to determine if I do or I don't have directory listing filters enabled.

Would you do me a huge favor and tell me precisely how to navigate to the switch, and what to enablwe or disable when I geth there?

Thanks very much.

User avatar
boco
Contributor
Posts: 24273
Joined: 2006-05-01 03:28
Location: Germany

Re: FZ 3.39.0 doesn't see var/www

#4 Post by boco » 2019-01-26 04:26

Menu View - Directory listing filters...

CTRL+I

Fourth toolbar button from the right
### BEGIN SIGNATURE BLOCK ###
No support requests per PM! You will NOT get any reply!!!
FTP connection problems? Do yourself a favor and read Network Configuration.
All FileZilla products fully support IPv6. http://worldipv6launch.org
### END SIGNATURE BLOCK ###

geomcd1949
500 Command not understood
Posts: 5
Joined: 2019-01-25 01:59
First name: George

Re: FZ 3.39.0 doesn't see var/www

#5 Post by geomcd1949 » 2019-01-26 05:38

Thank you. Found it. No filters were checked. Same problem remained.

Opened FZ using the terminal. That gave me access to /var/www/.

Now, however, every time I open FZ, I first must click out the message that says:

"An error occurred saving the transfer queue to "/home/george/.config/filezilla/queue.sqlite3".
Some queue items might not have been saved."

Any ideas on how to get rid of this message?

FZ works fine after I click OK to close it.

Again, thanks.

User avatar
botg
Site Admin
Posts: 31800
Joined: 2004-02-23 20:49
First name: Tim
Last name: Kosse
Contact:

Re: FZ 3.39.0 doesn't see var/www

#6 Post by botg » 2019-01-26 10:48

Where did you obtain FileZilla? It sounds like you are using a sandboxed third-party package.

geomcd1949
500 Command not understood
Posts: 5
Joined: 2019-01-25 01:59
First name: George

Re: FZ 3.39.0 doesn't see var/www

#7 Post by geomcd1949 » 2019-01-26 22:10

I may have messed something up on my system. I installed FZ 3.40. When it didn't work properly [problem detailed above], I uninstalled it and re-installed 3.39 from the Ubuntu Software Center.

User avatar
boco
Contributor
Posts: 24273
Joined: 2006-05-01 03:28
Location: Germany

Re: FZ 3.39.0 doesn't see var/www

#8 Post by boco » 2019-01-27 02:59

Please note that outdated and Linux repository versions are not eligible for support from here. Only the binaries from this site and self-compiled (to a degree).
### BEGIN SIGNATURE BLOCK ###
No support requests per PM! You will NOT get any reply!!!
FTP connection problems? Do yourself a favor and read Network Configuration.
All FileZilla products fully support IPv6. http://worldipv6launch.org
### END SIGNATURE BLOCK ###

geomcd1949
500 Command not understood
Posts: 5
Joined: 2019-01-25 01:59
First name: George

Re: FZ 3.39.0 doesn't see var/www

#9 Post by geomcd1949 » 2019-01-27 07:12

OK, understood. Thanks for all you've done so far.

Post Reply